Allen-Bradley · Kinetix 6000
2094-BC01-MP5-M Repair
Allen-Bradley Kinetix 6000 integrated axis module (2094-BC01-MP5-M). Accepted for evaluation with honest limits: full load validation of shared-DC-bus modules requires a multi-axis rack, and we disclose exactly what our bench can prove before you approve anything.
Known failures on the 2094-BC01-MP5-M
- ▸Axis module faults
- ▸Bus interconnect issues
- ▸IGBT failures
Ship your unit to
USPS
Control Board Lab
PO Box 120241
Arlington, TX 76012
UPS / FedEx
Control Board Lab
1009 Oakwood Ln # 120241
Arlington, TX 76012
Write your RMA number on the outside of the box and include it on a note inside. Units over 50 lb (large VFDs, spindle drives, industrial PCs in enclosures) ship by freight — contact us before ordering and we will arrange dock-to-dock shipping.
Check these before you ship
Some of these will tell you the 2094-BC01-MP5-M is fine and the fault is elsewhere — worth ten minutes before you pay to ship it.
- □Megger the motor and its cable before condemning the drive. A shorted winding or a cable chafed against the machine frame will destroy a replacement drive exactly as fast as it destroyed the first one.
- □Record the alarm code and what the machine was doing when it tripped — during acceleration, at speed, on a hard stop, or only when warm. That distinction separates a power-stage fault from a thermal or feedback fault.
- □Check whether the cooling fan still spins freely and whether the heatsink is clogged. If the only fault is a thermal trip, cleaning and a fan may fix it on your bench.
- □Confirm incoming line voltage and phase balance. Repeated drive failures on one axis are often a supply or wiring problem the drive is simply reporting.
Not your exact model?
Search the catalog or send us the number on your unit's label — we service far more than the catalog shows.
Why a 2094-BC01-MP5-M fails — and what we do about it
The Kinetix 6000 shares its electronics across the family, so these are the faults we see on this part number again and again.
Power stage failure
- What you see
- Overcurrent or ground faults, or a drive that trips as soon as it is enabled.
- Why it happens
- Output power device failure, typically caused by a shorted motor or a damaged motor cable rather than arising on its own.
- What we do
- The power stage is tested cold device by device and repaired, gate drive verified, and the drive proven under load.
Bus capacitor and pre-charge faults
- What you see
- Undervoltage alarms, or a drive that will not come up cleanly on power-on.
- Why it happens
- Aged bus capacitors, or a failed inrush limiting circuit that prevents the bus charging correctly. The second is much less serious than it appears.
- What we do
- The bus and pre-charge path are both assessed, the actual fault repaired, and correct power-up verified.
Repair or replace a 2094-BC01-MP5-M?
Servo and spindle drives are where repair economics are most favourable: the hardware is expensive, frequently obsolete, and often tied to a specific machine and parameter set. New replacements for older platforms are commonly quoted at multi-week lead times when they are available at all, and a like-for-like replacement still has to be parameterised and commissioned against the machine. Because a drive failure usually stops the machine outright, the number that matters is rarely the invoice — it is how many production days pass before the axis turns again.
- New replacement
- ~$3,488 distributor [REPORTED]
Market figures are collected from public listings and are indicative only — a used unit also arrives with an unknown service history and no warranty from us.
Full technical detail for this repair
The Allen-Bradley Servo Drive service page covers the complete bench sequence — how the unit is tested, what gets replaced and how it is proven before it ships back — along with the rest of the family we service.
Allen-Bradley Servo Drive Repair — full details →Frequently asked questions
Can the 2094-BC01-MP5-M be repaired?
Yes — axis module faults, bus interconnect issues, igbt failures are the failures we commonly repair on the Kinetix 6000 platform. It starts with a free bench evaluation and a firm quote you approve before any work — $0 if unrepairable.
How long does a 2094-BC01-MP5-M repair take?
Standard bench time is 3–5 business days once the unit arrives. Rush service (+$149) moves it to 1–2 business days, and emergency same/next-day attempts are available — contact us first.
How do I send it in?
Start the repair online to get an RMA number instantly, pack the unit well with the RMA on the box, and ship it to our Dallas–Fort Worth lab with any carrier. Full packing guidance is on the mail-in instructions page.
Machine down? Let's get it back up.
Start a repair online in two minutes, or send us the part number for a free technician review.
The Fixed-or-Free Guarantee: if we can't repair it, you don't pay for the repair.
Call (817) 799-7332 · 📱 Text us a photo of your unit · Email repairs@controlboardlab.com